Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello,
I have a BLE device with the nRF Desktop application, and I want to turn off my device if it is not used, even if it is connected to my PC. I set my CONFIG_CAF_POWER_MANAGER_TIMEOUT...
I am testing out the Bluetooth Channel sounding sample with the nRF54L15-dk board using the samples of Channel sounding Initiator with ranging requester. How to change the...
Good evening,
I have been working for a while on a project that requires the maximum possible speed from both app core and SPIM4 peripheral. To do so, I set the app core...
Hi,
I have an NRF5340 application based on zephyr which produces a combined merged_domains.hex file.
I need to add a post build command after the "merge_domains.hex...
Hello,
I have dts files defined with flash partitions which build & work fine on nCS v2.6.0 But the moment i add same definitions to dts of nCS v2.9.0 it gives me redefinition...
Dear Nordic
Q1.
We tried new nrf9151 IC at custom board.
IC version: nrf9151 AEA (Engineering B)
Firmware: ncs2.7.0 Serial LTE modem application + mfw_nrf91x1_2.0...
Hey everyone,
I am new to the development of Nordic chips so I might get some things wronog here or there.
I am using windows 11 and am trying to flash a nRF54l15 DK board...
hi,
When verifying the modem upgrade, if the network type is set to support both Cat-M and NB (AT%XSYSTEMMODE=1,1,0,0), the actual network that connects is NB, and the modem...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
Using an nrf5340 with nrf7002 wifi, connected via SPI4. Using a shared (chip) antenna, and the COEX signals (pretty much exactly as per the dev board schema).
DTS snippets...
Hi,
I am using the nRF54L15-DK and nRF Connect SDK v2.8.0 Zigbee-Addon.
In an environment with three devices: Coordinator, Router, and End Device,
When powering on...
I am migrating from the 2.6.1 development environment to 2.9.0 but am unable to compile due to some configuration issues.
My prj.conf configuration file is as follows: ...
hi destiny98 i also working on sending string from peripheral to central but central device not able to receive it and show the same message every time, here i attach code...
