Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We have been using the DFU that came with the sdk 12.1 with a modification (essentially removing the button from the DFU code). We currently send an application command that...
Hardware:
I have an nRF52 device running the S132 running as a Central.
I have 6 iOS/Android devices running as peripherals.
Background:
I am attempting to have my central...
Hello,
is there any good example available, with whom I can simulate, that there are two devices are already connected and the host is scanning for some other devices?...
I am trying to use the function or any function with my BLE UART application. I have a timer that expires to kickoff reading of some sensors and then when I try to read my...
Hi all,
i m connect a sensor with Nrf51822 beacon and get the data.
so i want to transfer those data to Nrf51 dk kit continuously.
where i want to change or put my data...
Hi,
I use nRF51422 in Dual mode(SD310) with SDK10 Version.
The profile is CSCS.
I want to ask
How to just show Speed Sensor or Cadence Sensor.
Here is what I did just...
Hello,
I'm evaluating the feasibility of using the nRF52832 chip on a board with a microprocessor running Android and I like to know if Nordic has released or is planning...
I'm using SDK nRF5_SDK_13.0.0_04a0bfd and compiling the example ble_peripheral/ble_app_hrs/pca10056/s140/armgcc using Eclipse Mars 2.
Flashing softdevice s140_nrf52840_5...
Dear Nordic.
I cant found stack API documentation for study.
All company give it for user, for example TI.
User open doc folder and can reed API.pdf file.
Where your...
I use NRF51822_xxaa, sdk12.2, arm_gcc 4.9_2015q3
when i flash hex file experimental_ble_app_blinky_pca10028_s130.hex from C:\NRF\SDK_12.2.0\examples\ble_peripheral\experimental_ble_app_blinky...
Hi,
i have NRF51822 beacon(PCA20006) and NRF51dk KIT(PCA10028).
I am connect a touch sensor and it's gives output in form of "HIGH & LOW".
and i am able to detect the output...
hi,
i want to connect sensor to nrf51822 to send data to smart app continuously over ble.i want to modify example ble_app_beacon. which functions i need to change?
Hi all,
I have implemented a service with various "long char" characteristics. The buffer that I use to receive the data wrote to the "long char" characteristics is this...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
