after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am running the "central multilink" example project UART connected with HWFC to an external host. The NRF51 adds about 3 uA of sleep current to the system and wakes...
I would like to use a Balun instead of discrete components for a nrf51822 QFAA package device.
Looking at the reference designs I found a handy integrated library that...
The jump from application to DFU is not working during buttonless DFU. NRFToolbox displays GATT ERROR. I use SDK 7.1.0 with SD V7.1.0.
In dfu_app_handler.c, I made the...
I want to flash a firmware on my nrf51822 module I was trying an example from Nordic, I concatenated the bin file with the s110 file and it worked fine. Now, when I went ahead...
In the nRF8001 Product Specification, section 7.1.5 it states:
"The maximum length of an event packet
is 31 bytes, including the length
byte."
In the headers...
Has anyone seen more than 3 notify packets per 7.5ms connection interval?
I am seeing 3 and am wondering if this is a fault of the way my app is working.
My Setup:
Nordic is the Server, Android is the client.
I have read many, many forum posts about doing long reads/writes. Virtually everyone says you cannot do long writes...
I am trying to connect more then one device to nrf51822 HID.
How can i pair more then one device ?
How can i delete paired device from nrf51822?
Thanks
Recently ran nRF Master Control panel on android and found "Read remote RSSI" button. Is data got from device in some way or simply measured by androd phone ble radio module...
I would like to write to multiple characteristics in a loop but the second call to sd_ble_gattc_write() causes a NRF_ERROR_BUSY error. From reading the documentation, I should...
Hi all,
I am working with PCA10028. I have a peripheral and central both are devices with no display and no keyboard. both peripheral and central device are under our control...
Hi,
I am using nrf51822 with s110 softdevice version 8.0.
Is there any way i can know the state of my radio at some point in the code execution?
In short I want to access...
As explained by electronut in his Blog and Lijun here , it is possible to program an External nRF51822 board using the SWD interface of the nRF51-DK.
But what about a custom...
I have a project, and nRF52832 it 's good chip for me, because it has NFC/ bluetooth communication.
I would like to know if nRF52832 can pilot epaper display. nRF52832 does...
