Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
Hi,
I am connecting a central to multiple peripherals. In order to optimize the throughput I would like to simultanuously sniff the connection. In the nrf Sniffer documentation...
Hello I am looking for the IBIS model for nRF52840 for signal integrity simulations. I saw similar requests older than 2yr and I am wondering if now the model is available...
We have developed a custom board with an external SPI flash, which I have tested and it works.
We want to use OTA over BLE, so we have added MCUboot to the project, which...
Hi, I am having problem making DFU work on nrf52832 using nrf connect sdk 2.6.0. Below is my mcuboot.conf under child_image and prj.conf. Please guide me where I am wrong...
We are producing an issue where the ZBOSS stack will emit a ZBOSS Fatal Error without any context if we alter ZB_DEV_REJOIN_TIMEOUT_MS. Specifically, the steps to reproduce...
Hello,
I am using a nrf Development kit and I have it plugged in into a mac laptop. It works fine, but I keep getting the message that says:
Disk Not Ejected Properly...
Hi all,
I am running the lsm6dso zephyr sample on my nrf52833 dev kit. I am unable to set the sampling frequency. I get this error after flashing:
This is my overlay...
I am looking into the possibility of using an nRF5340DK to probe SPI pins. For context:
There is a total of 3 devices in the system: the master and slave being used primarily...
I refer to and the answer answer given by AI referring me to you.
I need the lithium battery only to about 8-bit accuracy to reduce the leakage current. Please provide...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Dear Nordic
Last week our team concluded with PAwR functionality and achieved the communication between AP and Peripheral . We asked Nordic on private ticket( https://devzone...
Hello,
I used to develop for the NRF51822 using the NRF5 SDK in Keil, and I am now migrating my project to NCS. However, I cannot find my chip in the "CONNECTED DEVICES...
