Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
Hi All,
i have been working on two i2c devices
1. MPR121, which has slave address (0x5A)
2. PCF8583, its address is (0xA0).
I am using Zephyr I2c api for the same...
Hi,
I would like to ask on where can I find or set the advertising duration or on how long the advertisement would last?
I am using zephyr, nrf52840DK. I want to be able...
Hello,
So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link...
Hi,
Is it possible to perform a HW reset of modem core inside nrf9160 device? If yes, how is this HW reset requested?
Thank you very much...
Regards,
Emerson ...
proj.conf:
nrf52840dk_nrf52840.overlay:
code:
Pretty straightforward. I've looked through the nRF52840 Product Specification and there is no mention of data bits...
From zephyr/samples/sensor/lsm6dso, I found the following code using sensor_channel_get(). API from sensor.h.
}
However, there are more driver API in zephyr/drivers...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
I'm trying to connect my nrf52840 to the App but I have error message and impossible to continue ...
Here the log of the app standalone :
2022-10-07T21:50:58.341Z INFO...
During the software testing process, our device is connected to the rtt viewer for testing. At present, a problem is found during the test: sometimes the test engineer suddenly...
Can a single sdk_config file that has all possible macros definitions to use with an SDK
(1) be provided ?
(2) so that an identical sdk_config file be inserted in all...
