after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hey Guys, I am trying to program my nrf52832 board by connecting it with J-LINK(EDU) but could not do it. JFlash was giving failed to connect error. Even NRFGO Studio was...
Where could I find the nRF Connect v2.6.1 for desktop documentation? And more precisely, the one describing the Programmer official v1.0.0 functionality? As far, the only...
Hi,
I'm trying to get the scanning procedure to work while my device is connected to a phone. At the moment, even though I start the scanning procedure, I don't get any...
Hi,
I am using NRF52832 SOC for my application. I have developed application for beacon advertisement based on the nrf sdk. I am facing some issue in device advertisement...
I want create a simple application such that when I send a string "Hello" from the nRF UART Android app to the board, I receive a string "Hi" back to the phone. How do I write...
Hi,
I’m developing a BLE remote control device (S132 softdevice && SDK 15.2.0) . It works with NRF52832 programmed as a central BLE (I started from ble_app_blinky (central...
Hello, i am having problems with a loop in the function "flash_manager_wait()"; in the begining of the code.
main()-> initialize()-> mesh_init()-> mesh_stack_init(&init_params...
Hello, I have a discovery issue that seemingly only happens with the Samsung Galaxy S8.
I want to throughput test BLE5.0(2Mbps).
I using the nRF52832(BMD-300) with SoftDevice...
Hi!!
I'm adding spi functionality to S132 and SDK 14.0.0 ble_app_uart now.
The communication which added the function of UART to SPI and the sample code of ble_app_uart...
hello,
Now, i want to recover MAC from static random state.
for example, if MAC[5] =0X55 in chip itself, The MAC in adv in 0x1101 0101 ;
but i want mac in adv is 0x55...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I keep getting Mesh Error 6 while trying to combine the provisioner role with the client model. Which...
Hi,
I'm using nrf51822 with a custom board, where I should turn on a buzzer sometimes. I configure a timer and ppi to make a bip alarm. each bip lasts about 1sec; and the...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
