Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Working on a product with a couple to sensors with i2c communication. Are normally able read values from the sensors, but sometimes the i2c bus seem to be down. No more...
Hi,
I used sdk11 and sd130 at a 51822 project, it is required to be paired with a key for both andriod and ios, everything is fine but the dfu on andriod, I used nrfconnect...
SDK 14.2.
Application Timer Library
I had a question regarding the Application Timer library and the way it checks for timeout handlers. In the documentation, it says...
Hi, I have problem with nRF51822. I've bought cheap China miniboard with this chip. I can program some examples (precompiled HEXes) with J-LINK and they works correct, but...
Hi,
I want to make a program in order to assing functions to the buttons and manipulate movile phone apps without making any app or configuration into the phone.
What...
Hello,
I've a process, let's call it P1, that sends I2C instructions for a LED driver (it's like an infinite loop of I2C instructions for registers management that have...
Hi all,
I want to make touch button by my NRF52832 board . I am trying Csense_drv example but The value of change is constant when I log on UART . LED flashes continuously...
Hi Team,
I am working with Nrf24L01 chip with ATMEGA328(ATMEL C code) i made separate TX and RX module it works fine. But i want TX and RX in same module i done coding but...
Hi.
I am using SDK15 and want to control keyboard and mouse using HID with nRF52840.
I used the HID example to verify that the keyboard and mouse work when the button...
Tools in use, etc:
nRF5_SDK_for_Thread_and_Zigbee_v1.0.0
RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha
NCP example located in <InstallFolder>/examples/thread/ncp/uart...
I use nrf52832 qfaa b017351o ,some ic can run sdk11 dfu demo but some ic can't. Demo location .\nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132...
Hello,
We have a custom board based on nRF52832, built an application base on SDK V15/ble_app_uart
It works fine with Android: we can send string over BLE but it doen...
Hi everyone,
I changed the example ble_app_beacon from sdk 15.0.0 sd132 to be able to scan beacon besides transmit. It works well to scan beacons and I can get their UUID...
I am using SDK15 and S140 and nRF52840 as central. I plan on deploying a lot of temperature sensors each of which will
have a nRF52840 acting as a peripheral also using...
