I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I'm following "ble_app_uart_c" example and works very well with SDK 10.0.0. So now I want to communicate with HM-10 module, but this has one Tx/Rx Characteristic. Are...
Hello,
In my quest to monitor the activity of hundreds of nodes (directly addressable), I am facing quite an obstacle.
The small memory of the nrf52 (nice piece of hardware...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
Hi,
I'm trying to use the nrf52832 with a sdcard application in SDK_13. I based my code on the example provided and managed to get the sd card working without any problems...
The error "Unknown command add_pc_lint" appears when running the bootstrap command during setup. It looks like PC-Lint is an application for windows for software debugging...
Hello! I'm trying to find a list of boards that can be integrated into a circuit design which have already received compliance in the EU, UK and with the FCC. I found this...
Hello. i testing zigbee coordinaator example with zigbeee device. Device was joined to Zigbee coord/ network.
Couldn't i get device payload data in coordinator source code...
I have the UART configured using the standard boiler plate code, with flow control enabled, where the RTS output is assigned pin 5.
I have defined a GPIOTE pin 25 as an...
We are working on a solution that involves a central provisioner that provisions a MESH network of sensors that it subscribes to. We need to be able to replace this central...
Hi,
I am currently drawing up a schemtic involving the NRF52832 on Proteus 8.
I have been trying to find symbol, footprint, and 3D models of the NRF52832 online, however...
Hi!
We are using a custom bootloader for our device. Current version of this erases everything from 0x0 to bootloader start address, and then writes MBR + Softdevice ...
Hi,
I have a question about ADC reading in ble_app_uart__saadc_timer_driven__scan_mode in SDK 14.
Let's say I'm using a double buffer, and I have 3 ADC channels (so...
