Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear Sir,
I want to access two slaves viz. MAX30205 & LIS3DH by using nrf52832. The problem is, as per the datasheet the values of the pull up resistors required by both...
Cannot get nRF Sniffer version 2 (beta) to work properly with nRF52 DK running the sniffer_pca10040_51296aa.hex:
Windows 7 64-bit
nRF Sniffer 2.0.0-1.beta
Wireshark...
Hi All,
We are currently in the process of FCC certification for one of our product that uses nRF51822. Our testing house said the the test has failed because of not qualifying...
With a NRF51802 based product, we see DFU errors on Android devices in the field. Our config is: - nrf51802 with s130_nrf51_2.0.1_softdevice and nRF5_SDK_11.0.0_89a8197. ...
hi,
i am using sdk 14.1 nrf52840.
i am getting these 2 errors in keil
.\_build\nrf52840_xxaa.axf: Error: L6915E: Library reports error: __use_no_heap was requested,...
I want to use nested app_timer instances: I am gathering data on a repeating app_timer (app_timer_1) which fires say every 10ms. One of my sensors providing the data requires...
I am trying to call the bootloader by using the provided DFUService from mbed on the NRF52832 DK. Unfortunatelly the bootloader does not start. I made sure the Softdevice...
Hi,
In linker script `external/openthread/linker_scripts/openthread_nrf52840_dfu.ld` there is a doubled `crypto_data` section.
Is it added intentionally or just a mistake...
Hello Nordic-Team,
Where I can find 2.4GHz RADIO example for nrf52810 ( pca10040e )?
and what we need to know to porting 52832 to 52810 in RADIO?
Kind regards
...
Hi
I had downloaded latest SDK for Mesh 2.0.0 and imported the Light Switch example to segger studio, while building the project i'm getting an error as "board.h" not found...
Dear Nordic Team,
Thanks for supporting.
My application is central act as a non connectable scanner and display the advertising packet through UART without fail. Please...
Hi guys,
First issue: is that the mergehex.exe fails everytime when trying to Write the merged file. The Error is ERROR: An error occured while writing the file. this has...
Hello.
Now I'm using nRF51422 and SoftDevice S310. And I'm trying to pass Bluetooth Consistency Check and PTS.
I read this question and answer.
devzone.nordicsemi...
Dear Nordic,
I see nRF52832 already support Bluetooth5 on-chip from your offical website, we want try a long range case, but not find the relate code, is it supported on...
Hi - I have followed the compiling instructions and downloaded the project to the nrf52840 PDK and it does not work. By debugging, no error codes are there during the execution...
