Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I'd like to upgrade nrf51822 QFAC custom board firmware via DFU and change SoftDevice from s110 to s130. Because of larger (than s110) size of s130 I haven't enough...
Hello,
i am using the Visualgdb with sdk v 13.01. i have Nrf52840
i was trying to read the DeviceID of ADXL345
i am using API from this thread
devzone.nordicsemi...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
What I have to do if I met this ? I round length to fit (len+4-(len % 4)). Is it right ?
if (!(IS_WORD_SIZED(m_start_packet.sd_image_size) &&
IS_WORD_SIZED(m_start_packet...
Hello,
We have problem BLE connecting to the nRF52832, if we use the method gap_init(), the "better" smartphones can connect(those who support BT 4.2). If we skip the gatt_init...
Hi,
I'm trying to program an external NRF52832 board with the NRF52-DK, per the instructions in this post .
Programming works fine, but the code doesn't execute after...
Hi,
I'm trying to do DFU in my app, I almost complete it, I met a problem that my app flashed back when I sent 04 to the device.According to the DFU doc,after uploading firmware...
Hi,
I'm using the ADC of nRF52832 on nRF5 SDK V12.2. The setting as attachment. I found that it just do sample one time. But I have use timer to call nrf_drv_saadc_sample...
The scenario like this:
A is BLE peripheral with firmware (ble_app_uart under nRF_SDK_13.0.0_04a0bfd), if no filter,any central can cenncet to it, but I just want B can cennect...
Dear all,
Help please,
I'm evaluating ble_app_uart (Central/Peripheral) but I don't understand how to disable the echo I have on the RTT USB VCP
When I send data from...
I am using 3 nrf52 DKs with S132 and SDK13 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and added the relevant...
