Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi Guys.
I have compiled and programmed ble_app_uart program in to a nrf51DK (pca10028-nrf51488).
I downloaded and installed nRF UART V2.0 to android 5.1.1 .But while scanning...
Hi,all.i use pwm with sdk8.1 sample (SDK8.1\example\peripheral\pwm),my question is how to stop pwm and set the pin to low level? is my code correct?
my pwm init code:
...
I've a board with the nRF51 inside and a LIS3DH as accelerometer.
I already reflashed and I want to read the accelerometer values from the LIS3DH but I don't know where...
Hi Guys,
I tried to integrate the spi master project to ble_app_uart. For that I added the missing headers from spi project to ble_app_uart. And also I added the .c files...
Hi, Guys,
I am integrating the proximity app with dfu, everything else goes well. However, when I try to update bootloader through dfu, it failed. I check the MCP log,...
Hello,
I use S132 on nRF52 and do multiple roles.
When event BLE_GAP_EVT_CONNECTED is fired, role is invalid (0). How to know that it was a device or central event ...
I have developed an application for the NRF52832, initially with the Keil toolset and changed to Eclipse/GCC. The application works great when I build/load with the Keil toolset...
Hi,
I have an NRF 51 DK and vs. 11 of the SDK and just recently learned how to write some basic code and now I am trying to learn how to use ADC on NRF51. I am trying to...
I'm testing pairing and bonding with an iPhone running iOS 9.3.1 and nRF52832. I'm running into trouble when reconnecting to a previously paired device.
The first time...
Hi,
I would like to use SPI raw master library (used on application chip in serialization examples) in my own application.
First, to understand well SPI raw implementation...
Hi all,
is there any method to disable SWD in a way that every operation through SWD is blocked?
Do the MPU also blocks for reprogram the binary through SWD (maybe disabling...
Hello
I'm new in nRF51 SDK_11
In my tutorial I want to set a RedBearLab BLE_Nano nRF51 like Central.
I read the references in " developer.nordicsemi.com/.../a00066.html...
If I want to do a project following.
The central that has NUS service can connect to at least two peripheral .
Two peripheral also have NUS service.
I can receive notification...
Hi Guys, my project requirement is i have to make sure that my nRF8001 should bond with only one peer device. So i intend do a whitelist one peer device address, whitelist...
I'm trying to use 4 pwm by hardware
and 2 pwm by ppi.
It works pefectly purely.
and if softdevice included.
I have to change nrf_ppi_ to sd_ppi_ api.
and got no demo...