Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
is there a version of nrfutil that works on linux?
this one doesn't: github.com/.../pc-nrfutil
$ nrfutil dfu genpkg --application _build/nrf51822_xxac_s110.hex fota.zip...
Hello,
I have used ble_app_uart example and wants to transmit 12 bytes data over ble using this function ble_nus_string_send call.
In 1 second how many times ble_nus_string_send...
Hi,
At the moment I'm trying to make some current measurements with the new nrf52 dev-kit from the global tech tour. Unfortunately I'm not able to go into Idle- or even the...
Hi,currently i want to measure the current consumption of nrf52 DK. I followed the tutorial nRF51 current consumption guide ,and use the Power profiling application in the...
HI. currently, I have used the nrf52 board to test the power consumption of ble,I followed the tutorial nRF51 current consumption guide,loaded the Power profiling application...
I've got my UART (with fifo) functioning, and now I need to read in a string and determine whether to act upon it or not.
I'm using the s110 softdevice, and I found a BLE...
Hello,
i would like do Output over UART (printf) the UUID and the DeviceName.
I have the scanning data p_gap_evt->params.adv_report.data
When i would like to get...
I am using nRF52832 DK. I have connected our custom board using Debug out and loading code is successful for custom board. I loaded radio_test code.
Now I want to test the...
I use eclipse IDE as a builder. My toolchain is arm-none-eabi 5.2.0.
Compilation is for N52832 processor. I imported *.ld script files and startups from nRF sdk.
During...
