Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
Can I do something like this:
The SPI master sets CSN line low.
The SPI master sends multiple packets. And the total number of bytes exceeds the...
I want to transfer data collected in my nrf52DK to nRF51 dongle at regular intervals. Right now I can use master control panel in PC to receive the data. Is there any way...
I am using the bootloader from github here to upload DFU over-the-air using an android phone. It works fine for bootloader and application uploads. But if I upload the softdevice...
I'm looking for a radio module for a harsh environment (steelworks furnace)
The module has to work at high temperature 80°C and must transmit 16bytes every second at a distance...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi. I'm using PCA10028, SDK10.0.0, S130.
Recently I'm testing SYSTEMOFF mode.
Unfortunatly My board is not operate now.
KEIL can't connect PCA10028 baord any more.
Here...
i use a ppi channel 0 to connect timer2 and adc,when timer2 compare event happen,the adc task start begin.then,in the adc interrupt handler,i read the adc result into the...
It seems that many people use GCC toolchain (with "high" setup effort) for utilizing SDK in C++ development.
It should however be possible also on Keil with less setup effort...
I am currently using version 'NRF D 8001 1429SH' as printed on the nrf8001 IC
I have already managed to successfully bond with an android phone and completed the ReadDynamicData...
I am trying to migrate from using an earlier chip, the 8001 over to nrf52832 because we want to utilize new ble 4.1 features. The issue is we have another micro that was a...
Hello, i did not find any solves and i want to ask you are , how can i change my data in advert packet? I tried to do it from TIMER interrupt without advert time out and with...
I've been trying to import this NRF51 Eclipse project for a few days now, but no success.
github.com/.../HomeKit
I've tried to closely follow the steps outlined in this...
Hi all,
I have a PCA10040 board and want to try the BLE examples provided in nRF5_SDK_11.0.0-2.alpha folder. However, there is always a problem when flash BLE hex files...
Hello,
I have a capricious component on my TWI bus, and sometimes my nRF52 do an infinite loop in file nrf_drv_twi.c
in this loop
while (!nrf_twim_event_check(p_twim...
Trying to connect nRF52-DK with Nexus 5 (Android 6.0.1) SDK 11 NFC HRM example
But can see this device in paired devices list. Next time i do it it never attempts to...
