Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have a custom board (was built using the Nordic schematics provided with the Smart Beacon Kit). I am using J-Link LITE to try and program the board.
The board...
Today nRF Toolbox App on my Android 5.0 phone is only recognizing HRM code running on my nRF5182-mkit, not other examples.
Today nRFToobox and nRFUART2.0 Apps both...
Hi,
I hope use nrfjprog.exe to do following things:
HW: nrf1822
download s110 6.0
download bootloader
download firmware
write some values to certain addresses...
Hi,
I've tried to search the documents and the forum for an answer to my question, but didn't have much luck.
We have a custom board that uses a STM32 micro and nRF51822...
Hello,
I am currently trying to find out how the BLE devices keep their connections in sync. According to the spec, the peripheral can have a slaveLatency of up to 32s...
Is it possible to run Master Control Panel and the PCA10001(or the J-Link lite) at the same time on the same PC, or will that cause problems? I guess I could simply try it...
Hello, Can anyone point me if the nRF51 Dongle can be used for connecting the device with an Android mobile.
Have used this dongle for connecting with PC opening COMM port...
Hi,
When pointer the p_conn_params of ble_conn_params_init_t to NULL for ble_comm_params_init(),
the connection will be disconnected fast automatically, test with the...
Hi,
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash...
There can search for profiles using the search method of Bluetooth 2.0 (RFCOMM) connection is not a state in the PC Settings in Control Panel, why Bluetooth 4.0 (GATT) is...
hi guy.
i'm developing such a joystick device Board(HID) using nordic nRF51822, BLE mode.
i have tested many android cell phone & pad and i didn't have connection problem...
Hi,
I don't know if this is a dumb question or not, but here it goes.
Since I'm new to the nRF51822, I've been playing around with the ble_app_hrs sample project. To...
I keep getting an error:
../src/main.c: In function 'ble_stack_init':
../src/main.c:517:5: error: implicit declaration of function 'softdevice_ble_evt_handler_set' [-Werror...
I can't get Puck to work.
I did get it loaded on nRF51822-mkit, but
it doesn't advertise (can't see anything on App nRF MCP).
same hardware is working with mbed...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
