I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I am trying to generate a constant 250ms pulse on a certain pin:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER0->BITMODE = TIMER_BITMODE_BITMODE_16Bit;
...
I explain my hardware, An MCU + NRF51822, Communication is done via the UART TX RX between them, baud rate is 9600.
MCU through UART transmit data to NRF51822, then NRF51822...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi sir
In the Developed zone, I found how to read RSSI value as below. According to nRF51822 RM, RSSISAMPLE would be 0~ 127.
Actual RSSI is – (RSSISAMPLE) dBm. But, I found...
Hi
We are using the UART demo to communicate with the nrfUART app.There's a condition some
time when it connect,it will disconnect immediately,anybody know what's the issues...
I'd like to get familiar with implementing a blood pressure and heart rate monitoring Bluetooth device. Which development/evaluation kit is the best to get started with? ...
Hi,
I'm using the "ble_uart_project_template" I would like to put the "host" processor into a deep sleep mode to save power while the nRF8001 is still active.
Is there...
Hi,
Can anybody help me, thanks in advance.
What is wrong with NVIC_EnableIRQ(UART0_IRQn) - the execution halts when calling this macro ?
I'm working with Keil. ...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi,
I am working with Arduino/Ble Shield to implementing a keyboard device with some consumer control keys support,
My implementation will be based on hid_keyboard_template...
Hi Nordic folks,
I’m stumped by an an error in sd_softdevice_enable() that outputs this from my error handler:
[ERROR] app_error_handler (src\core_functions.c:183...
It clearly states in the nRF51822 Beacon Firmware Documentation that you need to use the Master Control Panel in order to connect upload new firmware.
Now that said, there...
Hello,
I'm using Win 8.1 BT LE stack to communicate with the NORDIC. I am using soft device s110. I use notifications to send data to windows which assembles a message...
Hi,
I'm writing a little piece of software using direct access to the radio registers in NRF51822. Is NRF51822 capable of calculating BLE checksum in hardware? As far as...
