Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Section 28.9.9 of the nrf51 reference manual shows the Config register has 3 defined bits, BBA. A is for Hardware Flow Control and is one bit, 0 or 1, which makes sense. ...
Hi,
I'm trying to add more user services to LBS demo. I generated 128b UUIDs for my services. Then I should add them to list returned by scan response in function advertising_init...
Hello!
Sorry for a new guy's description.
We had a device running in normal firmware application mode, and the Bootloader was programed. It's our goal to accomplish DFU...
Hello
I am using the nRF8002 kit. I would like to inform the host (Android app) when there is a long button press on the input pin.
Is this possible and if so which BLE...
Hi folks,
I was wondering if someone has a reference implementation of a bootloader that uses exclusively ANT technology to make DFUs, being it ANT-FS or any other alternative...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
This is something for the legal department.
You had some questions here about the RFduino before. This question is about legal obligations Nordic supposedly imposed on...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
I take the nRF UART 2.0 for reference. I make the nrf51822 be always sending packages ,and if it sends one package succussfully,and the smartphone just shows what it receives...
Hi guys,
Is there any way that I can re program the MAC ID of the nRF51822 devices through the SWD interface? I was able to do this using the UART interface with the BL600...
Got a Keil ULINKpro D debug unit with my Keil uVision\ toolchain license. However that doesn't seem to work with the Nordic nRF51822 on my Fujitsu module Development kit....
Hi,
I referred to the sample code "led_radio_example" and I think I might miss some thing so the program does not work.
The sample code indicates to use a terminal program...
Hi,
I am trying to understand the behavior of auto acknowledgement with payload for an application I am working on, I am hoping for some clarification on how ACK with payload...
I seem to be getting into sleep() fine with not able to connect to my app!
but getting back to work from sleep() is taking toll and its not working simply.
I'm trying...
