If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
I used to use the ncs1.2.0 SDK to develop a product for customers. Now I am porting it to the ncs1.9.0 SDK. During the adaptation process, I find that its control over SPI...
Hello,
I have a few queries:
I need to confirm that does Thingy53 board support TensorFlow lite. So, for my ongoing project, I am using TensorFlow to develop my code...
Hello,
I am facing an issue at running otbr docker conainer on my RPi4 with nRF52840 Dongle as an RCP device . I am getting this error on the logs: Aug 24 16:05:07 0e6bb978e199...
Hi!
I have tried to get the secure_bootloader working on the nRF52820, but I think the linker settings are not correct yet. Maybe someone here has already written a bootloader...
Hello,
I am trying to build OpenThread Radio Co-Processor (RCP) firmware for nRF52840 Dongle with the new nRF Connect SDK v2.0.2. My VM is running Ubuntu 20.04.3 LTS with...
Hello!
I have an application that makes use of the function sd_ble_gap_conn_evt_trigger_start() , present in v7.3.0 of the S113 , S132 , and S140 SoftDevices. Here's the...
Hi,
1. I can use Programmer in nRF Connect for Desktop to flash the hex file ( nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images\ble\nrf52832sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Greetings,
I want to write the nRF Connect SDK v2.0.0 sample "nrf9160/https_client" to the nRF9160-DK, but when I use "Flash" in Visual Studio Code, the following error...
Hi,
I'm designing a drone based on these three Nordic IC:
nPM1100
nRF5340
nRF21540
Let's Start with nPM1100:
Based on this Reference circuitry
I based my...
On SDK 2.0.2, I was able to load peripheral_uart with CONFIG_BOOTLOADER_MCUBOOT=y and successfully update both the app core and net core using the thingy53. However when moving...
