Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Specifically, the example is examples/ble_central/ble_app_uart_c
I want to first verify my understanding of this example. In this example, should I be able to type in my...
Hello,
I am currently trying to flash a nRF51422 chip that will be placed on a custom PCB board using the pin20 on the nRF51 DK board. I had connected the chips pins as...
Hi,
I'm using TIMER1 CC0 for SAADC sample triggering through PPI and it's working well.
In order to check sampling frequency, for debug pourpose, I'm using PPI fork for...
I've been using the radio functionality directly, without the nrf sdk. Everything works great for 802.15.4 transmission and reception with one really odd exception: packets...
Can someone please post a simple example of using the internal oscillator with BLE? Modifying the ble_app_blinky example to use the RC would be ideal. No matter what I do...
Hi support team,
Now i am trying to understand the LPN machenism based on the LPN example. I cannot make sure where the bear handler is started.
There is a function bearer_handler_start...
Hello,
I'm planning to work on a device which should have two nRF5340 modules on a small PCB (they will be max 2cm apart from each other). Both modules will broadcast data...
Greetings,
I am using the NRF53 DK along with the Zephyr/Beacon (nRF Connect SDK v1.91) example for an ultra-low power application. I would like to know how I can change...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
