Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
Hi Nordic,
My customer want to know, whether LLPM function and Multilink can coexist?
For example, when I use a central to connect with 4 peripheral devices, can I use...
Hello,
NCS1.8.0 Windows10 X64;
i2s test,see the source code ,
it runing ok;
but,when i change to timer send,got error.
i want to send data by timer,
source...
Hi Team!
I am trying to connect the Thingy 91 to nRF Cloud using a local provider (Vodafone Romania). I followed the getting-started video when setting up my device. However...
Hello,
I need to power the nRF52840 with 1.8V while keeping it connected to SES through USB.
I believe I have to proceed as directed at User Guide paragraph 8.3.5 “nFR52840...
Dear Concern,
We are currently planning a mass production of a product that uses nrf52840 USB dongle as a component. We are thinking of using JTAG debugger to flash the...
Hi,
I am getting a strange issue in my code where my FDS will run fine if there is no bootloader but fails to initialise if there is a bootloader present. I am using SDK...
Hi!
We are testing nRF9160 in an application were we monitor sensor in certain modules on trucks / trailers. Our test application is based on the Serial LTE sample application...
Hello,
I am new to DFU OTA on Nordic's chips and I am currently trying to implement it on a custom board with an nRF52832-QFAB chip.
This will be a long issue since I...
Dears,
I can't select a new operator among the list I have, when I put the command at at+cops=1,1,"20820" , I have the error: ERROR: -8 , could you explain me what is this...
Hi, I am facing an issue, I am developing nRF9160 based Product, get sensor data from peripherals and publish to AWS cloud.my firmware is based on AWS IoT sample. I observed...
