Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
We recently came across this network stack vulnerability called ripple20 and would like to know if there is any possibility of the same being present in the network...
Hi,
If i use nrf53 to interface with a modem(nrf91 or any other modem), is it possible to run the the TCP + TLS stack on nrf53?
In case nrf91 the the BSD lib runs on the...
Hello,
I am currently developing an Android library to connect a smartphone with a peripheral device that serves several bluetooth services. BAS, DIS and 2 other private...
Hi I have fired up nrf5340 pdk and downloaded the sample HRS hex images and I can connect using my phone app.
Is there a detailed step by step guide similar to the one available...
Hello,
I have a production device (NRF52840) running a version of the Legacy bootloader from SDK 11.0 and I need to update this to the latest secure bootloader.
Old Device...
Hello
I would like to add Power Management to the BSP example and I'm doing as follows (using SES 5.10):
add #include "nrf_pwr_mgmt.h" and nrf_pwr_mgmt_init(); to...
I have ~600 bytes of configuration data total that needs to be saved each after a sensor joins the Zigbee network, details like:
IEEE addr
end point
Join state details...
I plan to use nRF52832 BLE chip of your company. Now I have the following questions: If I use internal 64M RC, can I use Bluetooth function?Is the 2.4g transceiver accurate...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine, however...
Hi Nordic
We want to study the network id and node id fields in proxy beacon of BLE mesh protocol.
For mesh4.1 sdk light_server example, does it broadcast network id after...
I tried to make CSMA/CA perform on nrf52832 but the SDK example didn't have Energy detection (ED) and CCA sample
How to configuration Energy detection (ED) and CCA ?
If...
Hello,
I am using nRF52840, SDK16 & SoftDevice140.
I am integrating pm_init()(Peer Manager) into my project and I am getting error 0xFFFFB180 from mbedtls_ecp_gen_keypair...
Hello,
We are using the nRF52 DK board and Keil uvision 5.
Using SDK 17.0.0 we can successfully load and build the `examples`. If we choose `examples/peripherals` we can...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
