Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am setting a nrf52832 for an OTA DFU using BLE. I am on windows.
After managing to run the Secure DFU Bootloader following the getting started , I am trying to merge...
I'm using s140_nrf52_6.1.1_softdevice and nRF5_SDK_15.3.0_59ac345 on a nRF52840.
We are trying to verify that, indeed, we are successfully entering and using coded phy mode...
Hi!
I've been having some issues with the ppk recently. I've been trying to measure the current on our custom board but it was showing way too much so I tried on the DK...
What are the set of commands to send data from node (router or end device ) to leader through router,(not directly connected); in openthead cli mesh build example in https...
Hi there,
I have a question about using zephyr on my nrf52840-DK board: I want to set the system to run at 64MHz for Zephyr. However, I can't find an option to do that....
Hello,
in keeping with the low power theme, I'm looking for some help in understanding the relationship between the pcb thickness, antenna trace and range.
Using the reference...
Hi every one,
I am using mesh in uart_app
PROJECT-------->
I am sending data through nRF UART APP to BLE (in MESH condition) and the received data on BLE sending it...
Dear Sir/mam,
Could any tell what header file I have to include to resolve this error? Please see in the screenshot
And in which I am sending data using nRF UART APP,...
Hi,
The Segger software does not work behind a proxy server.
After installing and licensing it (by moving the machine outside our corporate firewall) we try to start...
Hi all
I am using nrf52 with max30003 to read full ECG and send it over BLE.
My data is acquired at 128SPS.
De default GAP settings are too slow to receive all the needed...
Hello,
we're trying to develop central BLE application on nRF52840 using SDK 16.0.0 and S140 softdevice to connect with BLE pulseoximeter (Jumper JPD-500F - it uses TLSR8266...
From the documentation i have found it seems all the nrf52 and the new nrf5340 are all "extended range" up to 105 degrees celcius.
I am evaluating an application where a...
Hello!
Thanks for your help last time, highly appreciated.
However I haven't got till actuall programming because now I can't upload hex files. I start Thingy:91 in boot...
