Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
I am working on a project which will connect to device having static mac address . My job is to make sure that the device will connect to device having BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
Hello,
I wanted to replicate and build the LED Button Service using my own custom service. I used the template BLE project as a starting point.
I am using nRF52 DK, and...
for (int i = 0; i < LEDS_NUMBER; i++) { bsp_board_led_off(0); nrf_delay_ms(500); bsp_board_led_on(0);
}
in this code only the first command gets executed.
It turns off...
Hi,
We have several boards on hand which fall into two categories:
Category A: Our application has been programmed with JTAG in the past
Category B: Out application...
Hello!
I'm trying to DFU an NRF52 device on a custom board using nrfutil
I'm able to DFU the device using the NRF Connect v3.3.0 software together with an nrf52840...
Hello,
My problem statement is something like this:
Implement a Transmit Enable (TxEn) on a GPIO pin.
TxEn should be initialized low.
TxEn should be pulled...
I am new to Nordic and i am using nRF52840 DK, - SDK 15.2.0 - s140. I have written an application by modifying the Heart rate Monitor example. My program acquires and sends...
hi,
I am working with usb dfu bootloader for nrf52833. I set the bootloader entrance mode to GPREGRET only. before enter bootloader, I set NRF_POWER->GPREGRET = 0x00000001...
I downloaded SDK V17.0.0.9 and opened BLE_APP_UART example from /ble_peripheral folder on IAR EWARM. I choosed ble_app_uart_pca10040e_s112 and compiled without problems. ...
Our system is currently using the ble_radio_notificaiton components provided by nrf5_sdk version 16, and we have noticed that occasionally after ble pairing + bonding operations...
Hi
I use nRF52840 demo board load the firmware( C:\sdk\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\cli\ftd\uart\pca10056\blank\ses )
the putty can work...
Hi Team,
We have developed our application with SDK v1.20 and as v1.30 is released so we moved to v1.30 and stick to it.But project is not opening in sdk v1.30 and got...
Hello,
if one wants to start the app from scratch, what is the right way to create west.yml file?
Say we want to start from NCS 1.3.0.
Thank you & best
Oleh
hello Nordic
i am using nrf52832, sdk 16.0 s132 v7.0.1
i used the secure_uart_bootload example, the start flash in the example starts at 64000, though in this link the...
Hi, I am working on nRF52840 DK.
I uploaded ble_app_template on board and now trying to connect with nRF Connect and getting the following issue. Any suggestions, please...
