Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Goodday
I have integrated the fstorage peripheral example with the BLE_beaconing example. SDK 15.2. I can read and write strings. I cannot read back the hex number if...
Hello,
I am using nRF52832 devices and calculating the distance using RSSI, but it is not that accurate.
Can you please let me know whether we can calculate the accurate...
Hi @ all,
I am trying to get the serial DFU process runnning. The process worked fine for nrf52832 and now I am on the nrf52840.
I encountered a problem with executing...
Dear all,
I'm new to Ozone and hope that you will forgive the simplicity of my question.
I'm trying to acquire a simple trace (Code Profile) of the blinky example with...
Hi
I am new to all nordic BLE modules, currently working on nrf52832 eval board. I am trying to scan the BLE Beacons "EDDYSTONE" and their RSSI level for my tracking application...
Dear Nordic
I edit the uuid from sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type), all can success but only one uuid start with 0xFB, when use 0xfb, nrf_app_uart fail...
Hello
I am using SDK 15.3 ble_uart_central and peripheral example.
I am trying to transmit an array of integers from peripheral node to central node. Please help me with...
I need to run gc because I get rc =FDS_ERR_NO_SPACE_IN_FLASH.
So I run gc simple as written in https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0...
Hi all
we used a nrf52832 to communicate over SPI and I2C at the same time with some sensors. This works fine.
At the moment I try to convert the project to nrf52810 but...
Hello,
does anybody now when the sniffer will support coded PHY?
I found a similar questions but no answer yet...
https://devzone.nordicsemi.com/f/nordic-q-a/42216/does...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
