Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
my current problem is, that my application is not running when flashing it via BLE DFU using nrf52832 on BLE Nano V2 and nrfConnect. But the same code runs fine,...
Hello, I'm having trouble opening CMSIS Configuration Wizard from SEGGER Embedded Studio on Ubuntu Linux.
I followed this video over here: https://www.youtube.com/watch...
Goodday all,
I have a few nrf52840 dongles that is not being picked up by the usb anymore. I have been looking for ways to reload them back to "factory defaults" but cant...
I'm using the bootloader_secure_ble example, nRF52832, SDK14.0.0, S132 v5.0, IAR 7.80, nRF Connect v2.6.1, and an nRF51 Dongle connection to the host computer (Windows 10...
The documentation on the SAADC peripheral driver is unclear about how the samples are handled. When I read the docs I was under the impression that when providing a multiple...
Hi All,
We are using nRF52832 in our product. We are facing issue to establish bootloader in it. We used example codes for bootloader.
Below SDK example and procedure...
This questions seems to have been asked before in bits and bobs, but it's been hard to get a full concrete answer to this, which should be simple (in hindsight) I hope.
...
I’ve provided radiated immunity test for our devise based on the nRF52832.
The test has been provided by electromagnetic pulse with a power of 10V/m ,duration 1sec and the...
I am testing on my own board. The SDK is nRF5_SDK_12.3.0_d7731ad IDE is IAR Embedded for arm 8.30, windows version. Softdevice is S130. chip nRF51822_xxAC.
The firmware...
Hi,
I am in need of merging ble_uart and proximity program.
is there any code already there
I need to sens the data from nrf to mobile and i want to know that the nrf...
Hello everybody, I am trying to exercise the DFU for mesh following the DFU quick start guide (v2.0.1). To put you in context I have four nRF52840 devkits, three of them are...
hi..
i am using nf52832 ... segger 15.2version ... while i am start to execute the code .. i am getting the error at nrf_breakpoint_cond ... then i tried to set breakpoints...
Hi,
I am new to software development and had a query about software version control with the Keil IDE using git.
As a beginner, I simply copied an example project in the...
Hello,
I'm on nrf52DK PCA10040, SDK15.2
I'm sure it's quite basic, but I don't get it. I just need to write actually two uint32_t value in flash memory (so FLASH_DATA_LENGHT...
Hi,
I have got a nRF542840 dongle, and I have installed all the required programs (I got all from this website: https://www.nordicsemi.com/eng/Products/Getting-started-with...
