I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I keep getting Mesh Error 6 while trying to combine the provisioner role with the client model. Which...
Hi,
I'm using nrf51822 with a custom board, where I should turn on a buzzer sometimes. I configure a timer and ppi to make a bip alarm. each bip lasts about 1sec; and the...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
Hello,
Thread Topology Monitor can associate an user name with a device. Where is it stored (in computer application or directly into the device) ? If it's in the device...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am testing the NR52832 using a BMD350 module on a custom made board.
Using the SPIM i faced the problem that i got an extra 500uA of current randomly. After trying to...
Dear Nordic,
We are using NRF52832 + RFX2411N for our product, and for lower the power consumption. we wonder if there has any way to know the CONNECT_REQ event.
In advertising...
After some time debugging an issue I had, I found out that my code was setting the I2C interrupt priority to 0, and at the same time that I'm running a Soft Device on my nrf52832...
Hi,
The Ch. 16 Power Supply Section of "nRF52840 Objective Product Specification v0.5" mentions the two power supply mode of nRF52840. This supply is available on the respective...
Hi.
I’m trying a multiperipheral function and have a problem.
The problem is I can not notify stable battery voltage with SAADC to the connected Central while advertising...
Hi, everyone,
We are developing BLE project on the nRF52832 chip (SDK 15.0) that must transmit to the big distances for about 20m. We set the transmission power to +4dBm...
Hi Dear nordic employee
I want to test the accuracy of my external LFCLK,
1、I enable the nordic RTC
2、set the prescaler 31（32768/32=1024），1/1024 second per step
...
The temp accuracy is stated at +/-5C. Does that include using piece-wise linear terms for accuracy? Is there any data on accuracy over a narrow temp range such as 0-40C? ...
Hei, I couldn't really find a question regarding this use-case.
I'm hoping to interface a USB (2.0) charging capability to my design and thus I need to have a communication...
