Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have noticed that there is a SB32 on the newer nRF52 DK boards (PCB 1.2.1), right next to the debug connector. It looks like this is a reference voltage that is...
Hi
I use the example "light_switch/server" project of nrf5_SDK_for_Mesh, and I want to add ble scan and connect func to the project, and make it possible be discoveried and...
Hi,
For a project we need to use mobile wireless communication in our device.
So we are looking if some design already exist with NRF52 ? And how to integrate it in our...
Hi All,
I am using SDK 14.0.0, ble_app_uart and fatfs example together. I am getting certain error and displayed below, please help me with how i can counter this:-
...
Hi all,
I am trying the port the peripheral UART example to the BLE_app_blinky and adding the respective libraries that are missing in the BLE app.
after I included...
Hi, there
i am using nrf51822 to communicate with quectel ec25 .i want to send AT commands over uart and receive some response from quectel.for eg. i am sending a "AT" command...
Hello,
is there any documentation about DFU init file structure (SDK 14.0)?
I used NRF util for creating DFU package, but i want to create my own app for that purpose...
From the SDK8 s110 device, I want to send the string("hello") to the other device via the uart, and in the meantime I want the battery voltage to come through uart.
I defined...
Hello every!
I was transmit data from point1 to point2 with two nrf52840 board. Now I want to do forward this data to point3. Can i do that and how to implement? Have any...
Hi,
I have used fstorage to save data in flash in SDK V13.0 with S132. But in the SDK v14, it have changed so many such as fs_config_t struct has been removed and I don...
Arms labs published some Bluetooth stack vulnerability
go.armis.com/.../BlueBorne Technical White Paper-1.pdf
Nordic answered that BlueBorce is no effect for LE.
...
Dear Nordic,
nRF52840 is very good solution and we are planning below.
What I want to do:
WLAN Firmware to be stored in nRF52840 Flash
nRF52840 Flash is sufficient...
When I am using power manage function to keep device low power mode, for every 6 milliseconds I am getting small spike of ~300 micro Amp and average current of 300 micro Amp...
