Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello !
I have a problem with my program (on a nRF52 board) : when I send a value to the board via BLE, it seems that my static variables are reset.
I noticed that, because...
I need to store data in some moments and if something happen i have to read those data, i have to do a log events.
I use nrf51-dk and soft device s130. This data is taken...
"....\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production. Please see github.com/NordicSemiconducto.. . to generate it.
i found...
nrf51 dk with 51422 device (10028) was running in Segger Embedded Studio example imported from IAR / Keil ble_app_cscs_pca10028_s130 SDK12.1.0 was just fine. I loaded couple...
Hi,
I'm new and I'm a student.
I have to connect the adxl345z to my board mb39c811-evbsk-02.
It has an nrf51822 integrated.
Someone can explain which pin of i2c/Gpio i...
We wanted to update the firmware over the air, We needed help for zip file creation(.dat file, .bin file and .json file). There are many links online, We needed an link which...
Hi,
I'm developing to NRF81522 mcu, using a softdevice S130.
The MCU is connected to another device through the UART peripheral.
I'm encountering the next problems...
Hi,
I am getting data from sensor and want to replace some new data with the older one in flash using fds. Right now,firstly i will write into flash by using one different...
I am using the nRF toolbox to upload bootloader and firmware to a hardware project. Our project requires the number of packets (found within settings > nRF toolbox > Number...
Hi,
I am trying to flash the blinky example from nRF5_SDK_12.0.0_12f24da, the program compiles and is also downloaded to the NRF52 DK successfully. But the LEDs are not...
Hello.
I´ve got problems with a via BLE connected IMU and data transfer over UART.
I´ve now tried several methods to implement UART connection but with the given baudrate...
Getting the error when trying to compile the C++ project with SDK 12.1.0 :
In file included from .../components/softdevice/common/softdevice_handler/softdevice_handler...
We followed this link devzone.nordicsemi.com/.../ , we loaded zip file in mobile(android 6.0.1). We are able to select device, we are not able to select file(Zip). The issue...
as I found the sample code in sdk12 , the bootloader is quite different with bootloader in sdk11,
event uuid has got changed, is it possible to be compatible?
dual bank...
