Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
In an RFID application, we have nrf24l01+ and SMT32F4xx on the Reader and nrf24lu1+ on the tag.
The Reader is acting as multiceiver currently.
Pipe 0 and Pipe 1 are...
Hi Team,
Is it possible to develop MCP like other application which runs on Linux (say Ubuntu) using BLE dongle?
Where to start for this!? Any guideline or documentation...
Can smone help me:
An error pops-up…
“
RESTRICTED VERSION WITH 0800H BYTE CODE SIZE LIMIT; USED: 0DC4H BYTE (172%) *
“
This could be due to EVAL version of uVision...
So I'm using Keil v5.18.0.0, MDK-Lite Version 5.18, nRF Beacon app version 1.4.2, android 5.1.1, nRF51822, and nRF52832 micro-controller
I can successfully connect te bluetooth...
I use nrf51822qfaa ,s110 V8.00,keil mdk V5 ide.
does advertizing data Length can more than 31 byte? why?
ble_advertising_init(&advdata, &respadvdata, &options, on_adv_evt...
hello everybody,
I'm working in a project and faced some problems : article_1 & article_2
the final thing I did is as the second article, I do bonding & added the whitelist...
I want to make a BLE central A that can only connect to a BLE periperal B, and central A can not connect to periperal C,D,E...and other devices, even if they have the same...
Hi Nordic support,
I check the serialization page ( infocenter.nordicsemi.com/.../lib_serialization.html)
And prepare a connectivity board as below for my host system....
I am working on a device where i need to sense proximity of a smart phone and then judge its exact position and then take action depending on the position. Below is my theoretical...
