Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am using Timer_2 with two CC registers configured, 2 PPI channels (one for each CC register in the timer), and one GPTIO_TE to make a PWM to control dimming on...
hi,
my nrf51822dk was downloaded s110 hrs demo,and it was advertising,i used a ble sniffer dongle to get the advertising data.the AdvData is "0B 09 4E 6F 72 64 69 63 5F 48...
Why is it a standard in nordic-supplied code to initialize structs with memset like so? An example would be:
ble_gatts_char_md_t char_md;
memset(&char_md, 0, sizeof(char_md...
//Edit:
So Hung Bui just told me in another question, that there is indeed a buffer of size 6 or so?
How can I decrease that to 1 (i.e. disable it) so that only the latest...
I have the nRF52 DK and cannot determine the silicon revision on it. Is it the 'Engineering A' revision and therefore is subject to all the Errata that is currently published...
there are 3 modules to test(A1,B1,C1)
*2. A1 connect with B1(B1 is master, A1 is slave), C1 is power off, B1 as slave attempt to connect C1 with BLE_GAP_ADV_TYPE_ADV_IND...
I need a PWM signal as outoput from the nRF51-DK. And I do need the softdevice. So I decided to pick the code from the nrf51-pwm-library-master and add it to my project(SKD...
Why I will restart the ADC is used to measure the voltage is greater than 1.2 V
void battery_start(void)
{
uint32_t err_code;
// Configure ADC
NRF_ADC->INTENSET...
I just assembled my first nRF51822 board and I was able to program it using an IDAP-LINK and a blinky program compiled with the Eclipse/GCC toolchain flashed via SWDIO/SWDCLK...
Hi all,
Due to the updates file structure introduces in SDK 7.0 I'm trying to figure our where everything has been scrambled to. Here are the items I'm struggling with...
Hello,I wnat to enter in dfu mode after each advertising.I don't understand which is the handler / function that are called when send a advertising message?How can I put the...
