Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I am moving from FreeRTOS to Zephyr. So I jused some of your simple example for trying to understand basics. I edited it little bit.
I have some default task from...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
To achieve the maximum transfer rate over ESB, I added the following expression to the ESB initialization function:
NRF_RADIO->MODECNF0 = (NRF_RADIO->MODECNF0 & ~RADIO_MODECNF0_RU_Msk...
Hello,
I am using nRF52832 DK board. I wanted to drive some o/p signal from the MCU. So for testing purposes, I just toggled one GPIO from the Timer CC channel. For that...
On a custom board, VDD and VDD_GPIO are independent.
Is power supplying VDD1 and VDD2 enough to program nRF9160 through SWD, or do I need to also enable VDD_GPIO to program...
hi everyone i have flashed dfu to my nrf52832 using the latest sdk 17 i have done all the process as mentioned updating the ecc, private key publickey etc but my board doesnt...
I have an application consisting of a Thread Leader and a number of SED children. The communications scheme is set up to allow both children and the leader to have CoAP servers...
Hi Nordic,
nrf5 skd for mesh 5.0, nrf52832, sdk5 17.0.2
Now I am developing a product like a gateway. We just figured out that nrf52832 communicates with external device...
Hallo, hope you are having a good time.
I am using nRF SDK 17.02 and uses SES as an IDE.
Soft device S140 7.2.0
I have an application running which act as a central...
Hello,
I would like to know if it is possible to provide an example based on the lte_ble_gateway sample for writing and reading the characteristic!
I changed the example...
Hi Nordic,
nrf5 sdk 15.2.0, nrf52832.
I am testing the UARTE with the example experimental_libuarte. I changed two functions like below:
1. nrf_libuarte_tx(): m_tx_len...
Hi,
I am using vscode with nrf pulgin for development. after adding mcuboot to the project, Which hex file name to be used for programming through nrf programmer?
I call the k_msgq_get function to get a msg,however it return -11,which is not explain in document.
code:
Raw_data raw_data ;
int rr = k_msgq_get (& df_packet_msgq...
Hello,
I am working with the 9160DK and the AWS IoT sample in NRF Connect 1.8.0. The app is usually able to connect to LTE but sometimes it gets stuck and never connects...
Hi,
I am testing simple code on various project on my custom board. I have 4 Leds on custom board.
for (int i=0;i<50;i++) { nrf_gpio_cfg_output(i); }
I have LED connected...
