I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Is there any simple sample application utilizing i2c communications for nrf52805?
In Visual Studio Code with installed nrf connect SDK 2.0.0 doesn't show up any code sample...
Hi-
We have implemented a custom authentication scheme using BLE and based on a successful authentication event we would like to dynamically expose an additional set of...
Hello,
Is an embedded C based implementation to serially transport firmware data to a Zephyr based MCU available anywhere?
Background:
I am working on a nRF52833 solution...
I have implemented bonding mechanism in nRF52832 firmware. But when I use nRF Connect to connect nRF52832 device sencond time. nRF Connect still request entering passkey again...
Hello
We have a product where the central can connect almost every slave. It works fine, but when connecting client slave it connects fine and finds service fine but always...
I am not using any wireless radio in my application with nRF52840 . What is the best practice to terminate ANT(H23) pin.Shall I connect it to the ground/pull up or leave it...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I've developed a BLE application where nRF52810 as peripheral and nRF52833 as central. The peripheral continuously...
Hi everyone,
I am developing android app. This app can control nRF5 devices. This is a kind of smart home project. I have 5 nRF in my house and these nRF devices control...
I wanted to make a timer interrupt I went through the devzone support and saw the following post
I have 2 questions
Question one
I am following the Zephyr API. I...
Hi support team,
I have searched the forum , the infocenter and the specification, but didn't find the relevant info about how a LPN node initates the iv update if a LPN...
I have custom nRF5340 code that includes application and bootloader for both cores. For reliability reasons, I need to run bluetooth behaviour from both the netcore application...
hi ,
I'm testing this example sdk17.1\examples\peripheral\usbd_audio\pca10056\blank\arm5_no_packs.
I tested the microphone and the headphone separately.
For microphone...
The last time nRF9160 GPS API was mentioned in v1.2.0 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.1/nrf/reference/kconfig/CONFIG_NRF9160_GPS.html) as was working...
I have implemented bonding mechanism in nRF52832 firmware. But when I request nRF Connect to connect nRF52832 second time. nRF52832 pm_conn_secure() return 0x3002 and nRF...
I'm trying to make a demo with nRF52840DK. And I want to power it using the coin cell. So I want to check the voltage (percentage) so that I can know how long can the device...
