Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
I want to have 2 applications running on nrf5340 CPUAPP (nothing on CPUNET) with app1 in flash and app2 (in RAM) getting launched by app1 once placed in RAM as a...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
Hi Team,
I have configured I2C0 for reading data and sending iqs323 and iqs7211a. i have configured overlay file according pin conjuration which is below.
Pin configuration...
HI
Currently using NRF54L15 with NCS v3.0.0 and the periodic_sync_conn sample. I have created sysbuild.conf and added SB_CONFIG_BOOTLOADER_MCUBOOT=y. After compilation,...
Hi all,
I’m working with an nRF-based board and need to via software disable the internal DC-DC converter and use the LDO exclusively for testing purposes. I’m unclear on...
To confirm, when connecting a power source to VBAT for the first time, nPM2100 will automatically transition to Active mode assuming the power source can deliver enough current...
The error started coming after updating the sdk version from ncs v.2.9 to ncs v3.1
[00:06:58.439,514] <inf> _https: Log:Sock before -1 [00:06:58.484,649] <inf>_https:...
Hello,
Going through DevAcademy SDK Intermediate and it mentions running 'west boards'. Doesn't work for me:
Any ideas ?
Sadly after weeks of little problems like this...
Below is my change, set options to BT_LE_PER_ADV_OPT_USE_TX_POWER
But it always display Failed to set periodic advertising parameters (err -5) , why?
My hardware is...
Hi again,
I'm having trouble with the Matter Test Harness. I have been running tests in isolation one by one and fixing issues the TH finds. Now I have run into an issue...
Hi,
toolchain:-v3.1.0,sdk:v3.1.0. i am using the vscode software for the development
Basically i am trying to connect the peripheral using the address (mac:- 7C:D9:F4...
