Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
Hi Nordic,
My customer want to know, whether LLPM function and Multilink can coexist?
For example, when I use a central to connect with 4 peripheral devices, can I use...
Hello,
NCS1.8.0 Windows10 X64;
i2s test,see the source code ,
it runing ok;
but,when i change to timer send,got error.
i want to send data by timer,
source...
Hi Team!
I am trying to connect the Thingy 91 to nRF Cloud using a local provider (Vodafone Romania). I followed the getting-started video when setting up my device. However...
Hello,
I need to power the nRF52840 with 1.8V while keeping it connected to SES through USB.
I believe I have to proceed as directed at User Guide paragraph 8.3.5 “nFR52840...
Dear Concern,
We are currently planning a mass production of a product that uses nrf52840 USB dongle as a component. We are thinking of using JTAG debugger to flash the...
Hi,
I am getting a strange issue in my code where my FDS will run fine if there is no bootloader but fails to initialise if there is a bootloader present. I am using SDK...
Hi!
We are testing nRF9160 in an application were we monitor sensor in certain modules on trucks / trailers. Our test application is based on the Serial LTE sample application...
Hello,
I am new to DFU OTA on Nordic's chips and I am currently trying to implement it on a custom board with an nRF52832-QFAB chip.
This will be a long issue since I...
Dears,
I can't select a new operator among the list I have, when I put the command at at+cops=1,1,"20820" , I have the error: ERROR: -8 , could you explain me what is this...
Hi, I am facing an issue, I am developing nRF9160 based Product, get sensor data from peripherals and publish to AWS cloud.my firmware is based on AWS IoT sample. I observed...
