I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello everyone,
I have some questions regarding the registers of the nPM1300 specifically for the load switches and LDOs.
In the data sheet in chapter 6.5 under "Load...
Dear Nordic team.
I am a beginner learning to connect a SPI devices with nRF54L15-DK but the program always reports errors. Here are my related codes:
nrf54l15dk_nrf54l15_cpuapp...
NCS SDK and toolchain: nRF Connect SDK v3.0.2
Boards: nRF52DK-nRF52832 , nRF54L15DK-nRF54L15
Issue:
After un-initializing and then re-initializing MPSL, MPSL no longer...
Hi,
We are using the nRF Device Manager app (Android) to update firmware over BLE to the nRF54L15 DK, and it was working fine until August 26, 2025, when the app was updated...
Hello, I followed the "DFU over UART" exercise of the intermediate lesson 9, and I have problems with launching the main application. I'm using nRF54L15-DK board, SDK v3.1...
Hello.
I'm currently migrating our existing application code to the NCS 3.1.0 SDK. As far as I have recognized, with sysbuild the child image build has been replaced. We...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hi, i am trying to onboard our custom board using a nrf9160 to nRF Cloud using this guide: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/nrf_cloud_multi_service...
Hi we are developing a prototype with NRF5340DK, for which we needed to control few set of GPIOs. we wrote our code in the assumption that it's pretty straight forward and...
Hi,
I just updated my vsCode extension and the visual devicetree editor stopped working
I can compile just fine but changing the DT will prove difficult from now on. ...
I used the official example provided by Nordic: github.com/.../nrf70-wifi-ble-image-transfer-demo . I followed all the instructions to complete the preliminary configuration...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
We just started a project to replace an old PAN1720 and decided to use the nRF54L15 based module. So I am just getting started with the VS code and zephry enviroment using...
The UART (Port 2) gets garbled after bt_enable(). This issue does not occur if actively Debugging using Segger.
The issue is also reproducible upon a settings_save_one(...
