I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
I am developing firmware for NRF52811, using SDK 17.1.0 and Soft Device S112.
I need to write a characteristic longer than 20 bytes. I thought it could be done with...
The bluetooth connection is automatically disconnected, and the reason is 0x3E. Is this related to the small RSSI value? I set the transmitting power as 4DB, and the RSSI...
Hello,
I'm exploring the nrf5340 controller with a Fanstel evaluation board (EV-BT40) I use the SDK V1.7.1 with vsCode.
Used example "Bluetooth: Peripheral LBS".
Connecting...
I've recently flashed USB CDC ACM example to NRF52833. Even though everything seems to be working, there is no COM port listed on Windows. I've also tried Zephyr's USB CDC...
I got 2 NRF52840-DK Development Kit recently. But for one of the boards, the programmer firmeware encountered timeout during upgrade. The other board did not encounter this...
Hello All,
I am using nRF52840 Dev-kit and SDK 4.0 for Zigbee and thread. Due to some functions, we are using SDK 4.0 for this project which is not present in SDK 4.1. ...
Hello
In my another ticket https://devzone.nordicsemi.com/f/nordic-q-a/81555/ncs-upgradable-bootloader .
I know there is currently no support for upgrading the bootloader...
Hello,
I build my project with “Visual Studio Code” and with “SEGGER Embedded Studio”. There are some warnings when I use VS Code. When I use SEGGER to build the code...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1
I have below structure to frame the data packet and i need to send this packet to another thread through MailBox...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
Dear,
we have found a strange behaviour when using the DTM in SDK 17.0.2 and 17.1.0. The problem starts from ble_dtm.c:1188 when comparing the parameter value with -30dBm...
