I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am working with nRF52811 and having a problem with programming and reading flash memory.
I am using J-Link programmer connected with USB.
In nRF Connect Programmer the...
Hello,
I am trying to run the demo thread DFU example by following the docs but without any success. I somehow managed to reach the last step where I have to set DFU server...
Dear Nordic,
could you please suggest what should be done to make USB console & shell options work? What should be checked?
It was quite fine on nCS v1.5.1, and completely...
hi support team，
customer want to setup a timer with 800 us and then 1200 us and then repeatedly without any delay.
for now i use timer to set channel 1 with 800 us cc...
Hi all,
I am using NRF5340 in my custom board. The spims are working well, they are developed by nrfx lib in NRF SDK 1.5.1.
However, after I updated my sdk to 1.6.1, the...
Hello,
I was looking over the board -nRF52 DK- and saw a solder bridge labeled as SB31. But I could not find an information about it in the documentation . Could you please...
Hi All,
I have developed a Bluetooth application with nrf52840, which can be upgraded through our own APP (implementation 'no.nordicemi. Android: DFU: 1.10.3'). However...
Hi All,
I need to do RSA encryption and decryption using nRF52832. I am planning to use mbed TLS library.
Can you please help me to share some example code which can I...
I have encountered some problems when trying to use ENC28j60 ethernet module with nrf52840dongle and hope to get some help from here. Problems:
No internet access on Ipv4...
Hi
I try to run a nRF9160 on a nRF9160DK with lowest power possible.
A wake up from pin and periodically from RTC is required.
In the nRF9160_PS_v2.0.pdf is IMCUON1...
Hello,
We have a Xamarin Forms application, which we use for connecting to nrf52840 device and read/write characteristics. We managed to do it using Plugin.BLE nuget available...
I have difficulties in decoding the nRF9160 GPS output data. I know that nRF9160 reports its GPS data in NMEA GPGGA format, however, I am wondering why the last number which...
I want a waveform as below for motor control. I am trying to create this using nrf pwm driver.
I set the pwm sequence as below and checked the output. 2nd duty repeat does...
