I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
My question, at the top of the document linked below it has the line “ This information applies to the following SoftDevices: S132, S140, S212, S332”
https://infocenter...
Hi,
We are developing the Bluetooth based weight scale product.
We have successfully developed the project using nrf52840 DK board but now we are planning to develop the...
Hello,
I am working on nrf5340DK board and with sample example central_uart. I wan to find at what speed the application clock is configured and also want to change it...
There are lots of questions in the community related to use of multiple advertising sets. Common answer has been that it is "not support at the moment", see e.g.
https:...
I am using nRF52840-DK as a BLE sniffer. I have set up Wireshark to sniff the packets. Between c entral and Peripheral, there is an authenticated LE secure encrypted BLE connection...
Hi,
I'm working with a modified version of the secure bootloader included in the nRF5 SDK 17.0.0. I'm using an nRF52832 to update an STM32 over the air.
I have two update...
Hi all, I need to use the nRF5340's SPIM4 peripheral for 32 Mbps communication. I see dedicated device's pins are pre-assigned on nRF5340 for SPIM4, ad I want to use these...
We have an nRF52840 connected to a SAM4e over SPI. The nRF52840 is the slave and the SAM4e is the master. The 52840 uses a SPI slave routine based on the SDK17 SPIS example...
Hi there,
When parsing the GPS data from the Thingy91's GPGGA format, I've received invalid from such parsers.
Invalid:
I'm still able to successfully parse the value...
Hi,
We used modem fw 1.2.3 ncs 1.3.0 before and got upto 8 satellites when searching for a fix.
Using latest modem firmware 1.3.0 + ncs 1.5.1 we see no more than 3 satellites...
Hi,
I'm using the nrf52 mesh sdk v5 to make a provisioner based on the provisioner example of the mesh sdk.
During some provisioning, the provisioning process timeout...
Hi
in communication networks, GPS is often us to sync network elements and to get accurate timing.
with nRF9160 MFW 1.3, "GPS time based configurable IO-pin / pulse" is...
Hi!
I am developing an application that starts and stops gps occasionally. I am running the gps in GPS_NAV_MODE_PERIODIC with a timeout of 100s and an interval of 240s....
Hi,
We are having problems with nRF52840 dongle.
Intermittently pc-ble-driver-py throws the error in the subject when trying to open interface to nRF52840 dongle. After...
I got an average DRx power consumption of 415.03 µA for 2.56s in the Online Power Profiler for LTE. But unable to get the average power consumption of eDRx.
In the following...
