I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I tried to combine the Wireless_uart example with the USB CDC example to be capable of using both but it doesn't seem to be working.
When I plug my board using the nrf USB...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
I performed below mentioned steps:
Downloaded SDK 12.1.0
Soft Device s130_nrf51_2.0.1_softdevice.hex
Built secure boot-loader with new public key
Built project ble_app_hrs...
I'm trying to compile hci_usb sample of Zephyr with Nordic Connect SDK v1.3.0 using Nordic's proprietary controller but apparently it fails.
I'm using following configuration...
Hi I'm doing the Bluetooth GATT: How to Design Custom Services & Characteristics [MIDI device use case] example ( https://www.novelbits.io/bluetooth-gatt-services-characteristics...
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer. My setup: HW: PCA10040 1.2.4 SDK: 15.3 Project: \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral...
Hi
I'm using SKD16.0.0 and S132, and I want to realize that peripherals can only connect to a center with a known MAC address through directed advertising. How should I...
Hi Folks,
I am getting in trouble with SoftDevice activation. Indeed, my application did not return from the "nrf_sdh_enable_request()" call, more precisely it hangs into...
Hello,
I am currently working on BT840 and BT832 modules and trying to run the sample codes which are given by Nordic (specifically ble_app_uart which runs with UART service...
Hi,
there is a number of tickets on the sd_ble_gatts_characteristic_add, but I still can't get where I do it wrong :-(
I'm trying to initialize the battery service using...
