Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi
We need the recv() be blocking until the full amount of requested data can be returned or the operation was timeout, how to achieve this?
I tried flag MSG_WAITALL but...
Hi. Can anyone think of a way to use the nRF52832 (probably Timer) to detect approximately 125KHz-150KHz variable square wave down to about a 1Hz resolution? I'd like to detect...
Is there any example for Directed Advertising? I'll design my NUS central and peripheral use Directed Advertising, because I would like to have other bluetooth devices connected...
I use this code below mentioned in this question https://devzone.nordicsemi.com/f/nordic-q-a/26030/how-to-reach-nrf52840-uarte-current-supply-specification
This can reduce...
Do you have any recommendations, tutorial, blog, or getting starting guide for a developer wanting to use Mesh and BLE on the same node? Any information would help. Does one...
Hi,
After long use of BLE communication I sometimes get return code 8 from sd_ble_gatts_hvx.
My questions:
1. This return code is cryptic. Is it associated with defined...
I am trying to configure the CryptoCell on an NRF52840 to use AES-CBC encryption with PKCS7 padding. When I call the following function, it returns SASI_AES_ILLEGAL_PADDING_TYPE_ERROR...
Board: nRF52833 DK
Version: 1.0.0 PCA10100
SD: s140
Env: Segger v4.52 (installed on 5/10 via Toolchain Manager)
Hello all...
I'm running into a problem with the...
I have to write this page in case of the application firmware update, so I have to unprotect it in the bootloader (in the nrf_bootloader_app_start_final() function). won't...
We've been hunting down an issue there when we call nrf_drv_uart_uninit() we get a high static current which indicates that a clock or peripheral is being left on.
After...
I am getting the error:
There was an error adding your device: No device found with id 'nrf-352656100878829'. Verify you are passing a valid device id and not a device name...
Hello there
I am now using Nordic 52840 dongle hardware ready to be used as a zigbee sniffer, and I have seen that official documentation is feasible.
My current environment...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
