I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
My aim is on button press in peripheral side ,it should do advertise and sent data from single peripheral to multiple central(total two central).
I am using nrf52810...
Hi,
I am using nRF52840 SoC as a thread device in my application. I want to push data from sensors to cloud. So I need to configure one of my thread devices as border...
Hi Dev team,
I had an issue regarding getting the real time using RTC. I tried to follow the below dev zone blog but the CAL_RTC does not work in my code.
As such, I am...
To the kind attention of Nordic support team,
We are doing EMC pre-tests of our products using your nRF52833 .
At this stage, nRF52833 device is triggering itself a...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
Hello -
We are working with the nRF52840 and SDK v17.0.0 and tuning our power consumption during System ON sleep. We understand how to wakeup the device using the RTC and...
Hi,
I have encounter a problem that the first button release event is missing if the key is pressed while powering up.
The SDK I am using is nRF5_SDK_17.0.0_9d13099. ...
Hi!
We are using nRF52832-QFAB (B0 variant) in one of our projects, and it works fine and well.
We are now in the process of using the nRF52832-QFAB-E0 in the same build...
how can I work it use nRF5 SDK 17.0.0? On https://developer.nordicsemi.com/nRF5_SDK/pieces/nRF_DeviceFamilyPack/ the newest pack is
NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Support Team,
An error occurs when generating a signed binary file for central_dfu_smp.
Error: Header padding was not requested and image does not start with zeros...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
Hello!
I've only used the DK board so far, so I've rarely used an external debugger.
I'm going to use a custom board later, so I'd like to learn more about how to use...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
