I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
I am hoping to pass data from the nRF52840 to the nRF9160 over UART_0, on a custom PCB. For context, the aim is to pass data at a rather quick rate and good reliability. The...
HI,
I want to make a receiver to get BLE packets on any channel.(NO SOFTDEVICE)
I fail to fullfile it yet by reading <nRF52810_PS_V1.3.pdf>.
Any other hands can give...
Hi,
I am working on the asset_tracker application example on a Thingy:91 device. As I understand it, to activate the GPS it is necessary to keep the button pressed for a...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
Dear,nordic:
Please help me solve the exception encountered during the MQTT connection
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hello everyone a basic question but just to be sure.
I would like to make a custom board and I want to program this board with segger Embedded studio, should I just have...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
It was my idea to compile the mqtt_simple vom v1.3.0.
I spend now one week with your sdk. I tried it with SES and also with command line. Absolutly nothing worked.
The...
I am using a nRF52840-PCA10059 dongle to acquire data at a high rate (between 50Hz and 400Hz).
The connection is very unstable, after some seconds of acquisition, it sort...
We recently bought four 'nRF 52840' dk boards, and are trying to do board to board (non-mesh but single) wireless connection. However, there are just documents of mesh-communication...
Hi all,
I'm running into trouble using openocd to flash code onto the nrf52840 and then step through it. I'm running High Sierra (although I doubt that's important), and...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to picture.) Which Interface...
I have developed an app with DFU using SD s112(version 5) for custom NRF52810 board.
Q1: I want to update SD s112 to version 7. is it possible ?
Q2: how ?
