Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
