Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
Hello,
i noticed that even i send AT%XMODEMTRACE=0 with response "OK" the bsd lib triggers EGU0 / Trace interrupts. The modem is not started, but the bsd lib got succesfully...
We are using a Raytac MDBT42Q (nRF52832) Bluetooth in one of our products.
We are using nRF Toolbox for Android/IOS for testing. Is there any Windows 10 nRF Toolbox??
...
hi guys, I'm confused about bluetooth 5. Is there some example that use it? i have a nrf52840 board and i will like to use it in order to send my data but i didn't find any...
HI
I am trying to develop a mesh network using nordic mesh SDK..where nrf52 dongles will be beacons for which beaconing example will be used and from SDK
52840 DK will...
I startet evaluation with nRF52840 and SES.
I found the BSP Demo to crash (HardFault in Debug) after app_timer_init() , because of a NRF_LOG_INFO() inside, but Logging not...
Hi Sir,
As the title, can 51824 support BT 4.2 in Zephyr? Any document (or link) descript this?
If yes, which SDK version we can use?
Thank you.
BRs, Han
Hello,
I am working on nRF9160dk. I want to send gps coordinates via sms using nRF9160dk. Last week, I tried simple_at program to send sms and it worked. Now I am working...
When I am receiving data from slave data is missing. Means if o am reading 255 bytes then 127 bytes are right after that I am receiving alternate bytes. Some times I am receiving...
Hi,
I was wondering if anyone has sample code that would support a 16 x 2 LCD over an I1C interface.
Something like this.
https://www.amazon.co.uk/HALJIA-Character-Backlight...
hi,
in the SDK15.3，I successfully ported the DFU demo to app_uart, but the 52830 will enter the upgrade state each time after downloading the program. I want to know how...
I am following the steps mentioned in the "Getting Started Assistant" and downloaded the Segger Embedded Studio link mention in part #3. When I double click on the " SEGGER...
