If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
pls advise if nrf9160 DK can work in RDP protocol , say the board is in US to work on NBIOT carrier or LTEM carrier . Can it be configured in some way to do evaluation remotely...
Hello!
It seems to me that GCC compiler optimization (-O3 -g3) somehow break the SAADC.
When enabling said optimizations the SAADC no longer gives me valid measurements...
Hello,
I'm developing a gateway and i would like to use advertising packet on sensor side to transmit data but it suggests that my gateway will be in permanent scan. I know...
Hi , I would want to establish a GATT Server application as well as integrate Bond Management Service from glucose example (ble_app_gls) in examples folder of SDK15.3.0_59ac345...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
Hi,
I am using NRF51422 dk board in our project.We are using SDK 12.3 version , soft device S130 and keil u vision. Here the problem is I am not able to connect the bluetooth...
Hello:
I am able to debug and output to the J-link RTT Viewer(V6.44e) and when I stop debugging or sometimes randmley, the Viewer will display the message
"Warring:...
We're using SAADC to monitor two different voltage rails in different combinations (sometimes one and sometimes both).
I'm experiencing an issue in the following scenario...
Hi
I followed below tutorial, and I tried to send scan response data
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising...
Hi, everyone,
We are developing projects with nRF52832/51822 chips by using development board PCA10040. The programming of the chips is done by “nRF Connect\Programmer”...
Hi,
I have a problem with the app timer firing incorrectly.
I am using development board nrf52840-DK, Segger Studio 4.22, SDK 15.3.0_59.
When there has gone more than...
Hi
I'm really new to this filed and don't know anything about antenna, please forget me if the question is stupid.
I have an nRF52 DK, I noticed the Bluetooth antenna...
Hello, guys!
Here are the details about my development environment:
SDK = 15.3.0
IDE = SES
SoC = nRF52840-based BL654 module.
In my design, I need to drive a buzzer...
