I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm using nRF51822 and SDK 10 , Softdevice S110 . I enabled whitelist option in my application its working as expected, but when after device is resetting peer device data...
Hello,
I am working on an application on a nrf52840 using soft-device 140 and SDK 15.3. I have written 90% of the application using the ble_app_uart_c as a template for...
Some context: I am using an nRF51 with SoftDevice S130, which acts takes both central and peripheral roles, and uses UART to communicate to a peer MCU. I am currently facing...
Hello,
I am using Seeger for Flashing code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”. I have few queries on write data into Flash...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
SDK: 15.2.0
SoftDevice: s140 6.1.0
Hello,
I seem to keep finding conflicting information on how the NRF52 manages power to its peripheral devices and whether the application...
Dear proffesionals,
I am very beginer to nordic chip.i am using nrf_SDK_15.0.0_a53641a version.i am trying to integrate the writable_ndef_msg file to bluetooth.so how to...
Hello,
I am using custom hardware with an nRF52810 chip, connecting it to P16 connector of the power profiler kit. I use the power profile kit to check power consumption...
Hi guys,
I am a newbie in nRF but with some experiences in embedded systems . I have just been asked to work on a project that connects a nRF52811 to a nRF91.
I initially...
I'm testing a gps sample program below. github.com/.../gps
I have two questions about it.
1. It doesn't acquire NMEA data. it always stops working when it reaches 30 sec...
Hi
I tried to connect my dongle to PC but it is not getting detected , Even the red LED is not blinking., Can someone help me out with this issue
Thanks
Tabassum
I'm using LPCOMP to sense multiple input.
I call the lpcomp_read() function below for each input pin.
If I only call this function for 1 pin only, it worked fine.
For...
Hi,
I'm developing an application requiring multiple connections to several peripherals from a single central. I followed the instructions given here https://devzone.nordicsemi...
Does anybody know a quick and easy way to disable the radio functions in a soft-device application?
I want to measure and optimise the power consumption of all the other...
Hi
Can someone suggest me how can i erase the secure bootloader from nrf52840(Dongle),Because am unable to get "erase all" or "erase and write" option in nrf connect application...
