Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
Hi Nordic,
I have been trying to communicate with KX 124-1051 using IIC in nRF52832 . I am getting NACK from slave every time i send the device address. I checked all the...
Hy to everyone
I'm working with SDK15.3 Ble_Blinky example for my nRF52840 Dongle (pca10059).
First to know, I'm wokring with c++ and the whole Project is compiling without...
I'm using this module to develop a toy that needs a couple of sound effects. I just don't want generated tones but previously recorded audio files no longer than one second...
I wanted to try the bootloader related example. I was using the IAR to run peripheral examples.
But for bootloader example, I saw that IAR was not listed. So installed the...
I read the following QA - https://devzone.nordicsemi.com/f/nordic-q-a/41237/on-dfu-jump-address but still have doubts
1. Is it safe to set the Bootloader RAM start address...
Hi,
Hardware：nRF52840 module, Power Profile Kit. SDK：nRF5_SDK_15.2.0_9412b96.
Using Power Profile Kit to measure the low power consumption current of an nRF52840 product...
Hi,
I am currently trying to use SDK 15.3 secure serial UART bootloader (from the example in nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart) on a custom...
hi, I am working on the bootloader with s132.5.0.0 on sdk14.2.0. I am trying to using the uart to flash the chip.
I build the bootload example bootloader_secure_serial,...
I'm using three PCA10056 boards to test mesh example(Meshv3.1\light_switch).
[light_switch_client] ---> [light_switch_server1] ---> [light_switch_server2]
*Put the server2...
I am testing a mesh network, using the NRF52832 modules, SDK 15.2 and MESH_SDK 3.0, provisioning the nodes with nRF Mesh android app and using a modified firmware for the...
I am trying to build UART support into my current project but the compilation of the nrfx uart driver fails. See error below:
Any idea how to solve this? Is there good guide...
Hi,
I'm using the NRF52840 with the "nRF5_SDK_for_Thread_and_Zigbee_2.0.0".
I tested the zigbee light_bulb example and zigbee light_bulb + ble. It works fine so my next...
