Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
1.HOW TO enable a node relay , friend,proxy or low power ability ?
2.if node A publish a message to a GROUP ADDRESS(0XC001) for node B( subscribeed this group address) ...
I looked at the nRF91_DK_User_Guide and it is very confusing to understand how to set up the board for current measurements. The figure says to solder SB44 and SB45 but the...
Hello,
As of today, April 17th 2019, I am using latest version of SDK and SES. I am using Jlink from nRF51DK and a nRF52832 module bought from ebay.
I tested several examples...
extern void bsd_recoverable_error_handler(uint32_t error) AND
extern void bsd_irrecoverable_error_handler(uint32_t error); Will return various error codes - is there a list...
I'm trying to use the NUS to send data over from NRF52 dev kit to the NRF Connect app. Using Putty for UART works fine. Now I adapted to read out ADC values from 2 ADC ports...
Hi, can someone tell me what chip this is and where I can find the data sheet? Or at least if this is a custom fabrication, what chip from Nordic is it based off of? Thanks...
Hello,
I am using ble_app_uart_c example for my nRF52832 based central application. I would like to modify Tx Power and MODE of my device.
As per datasheet, I should write...
I'm finding above examples in SDK example file. but, can't find.
where the perfectly tutorials?? It's too hard for me only refer to the library's code.
I cannot config...
It has possible to add iBeacon advertising structure to add ble_app_blinky example code. I'm implement connectable iBeacon advertising every 5second it's connected nrf connect...
According to some benchmarks shown here: https://www.novelbits.io/bluetooth-5-speed-maximum-throughput/ , I should be able to get a connection speed of around 120,000 bytes...
Hi,
could you please tell where can I find a table showing all the NVIC interrupt vectors?
I searched in the nRF52840 datasheet but I did not find something relevant ...
Hi,
I am using an nrf52840 on a custom board with the 6.0 softdevice and 15.0 sdk. The I2C bus is running at 400khz.
I am reading 4 bytes on the i2c bus. The initial write...
Regarding the nRF9610 and the nRF9610 DK.
Am interested in developing a use for the Australian region (ACMA/RCM compliance) and have already worked on CAT-M1 devices for...
Hello,
I would like to know if I can use "NRF5 SDK" to provision bluetooth mesh device from other chipset provider ? Does licensing terms allow to use of SDK with 3rd party...
