I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello, I just want to set one random static bd addr using mesh SDK v3.1, and it seemed I have set correctly, but the SOC(nrf52840DK) still use the default bd addr which is...
Hi,
I'm using nrF52840 to connect to a PC via NFC. First is was OK, but after that I added an encryption to my application.
In order to do that, I changed the NFC_PAIRING_MODE...
I have a simple central device where a gpio triggers the device to scan and connect to a peripheral. This is running ok on the PCA10040, and also on a separate hardware platform...
Using the latest version of Bluetooth low energy (V2.2.1) running on nRF Connect V2.6.2 I was never able to connect to a peripheral device.
The peripheral devices are based...
I'm using Nrf52840 as the MCU for my circuit board, now I need to use it to transmit audio data which is 16bit, 16KHz PCM format(mono channel, therefore 256 Kbps) to the external...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Ftwi_master_with_twis_slave_example.html
Testing
Test the TWIS slave and TWI master...
I followed the steps in Getting Started Assistant to load the asset_tracker application using SES(4.16) and it fails with the following error.
CMake Error at /Users/myfile...
Hello,
For ble communication in an application, I am usnig NRF52832 based boards. I am using ble_app_uart example for peripheral and ble_app_uart_c example for client. I...
I am using the nrf51422 development kit with sdk11. I am running the proximity application for the battery life service. I am inputting voltages ranging from 3000 millivolts...
SDK14.0.0/S132 5.0.0
The SDK provides an example of turning on SSP Debug mode for LE Secure connections
Is there a way to enable SSP Debug Mode for BLE Legacy Paired connections...
Hi , I have some issues with the ADC. When moving in and out from low power mode the ADC isn’t working correctly. I am using the nrfx_saadc driver. When moving to low power...
Hello Nordic Team,
I am using nRF52840 Dongle (PCA10059) and nRF5 SDK. I was tring to use PWM example code (PATH - "nRF5_SDK_15.3.0_59ac345\examples\peripheral\pwm_driver...
Hi.
I build application which is mix of writing QSPI to external NOR FLASH, using linkage list base on the fstorage FDS example all in the embOS (RTOS of Segger).
I have...
Hi all,
I using nrf52832 and segger IDE
I am trying disable softdevice and enable it while chip running. In my project, I use RTC1 for app timer.
When I disable SD,...
My setup:
- nRF52840 Preview DK (though i have tried this on a newer version too)
- 3.3V separate supply
- DMM (Agilent 34465A)
DK Connections:
- SW9 is set to...
