I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I am trying to use BSP button event to take the system into sleep mode. A long push turns off IO and calls power management shutdown and the same button is configured...
Hello community!
I use the dongle PCA10059 (nrf52840) for my hardware. I already enable -DARM_MATH_CM4 and link library libarm_cortexM4lf_math.a with CMake. I can include...
Hei,
I am following the Install the toolchain section and after running
choco install python
the step does not verify because it does not find pip3.
'pip3' is not...
One of our resellers is requesting a classification code for the RF protocol. We use a Proprietary RF protocol based on ESB (Enhanced Shockburst). Is there an IEEE or a different...
I am experimenting with trying to improve the current range of gzll nRF52840 dongle to dongle (which is not that far from what I need). I am developing using nRF5_SDK_15.2...
Hi,
The top level page nRF5 SDK Documentation Library page ( https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/index ) contains a link to "S140 SoftDevice...
Hi,
I am trying to implement the DFU example from Mesh 3.1.0SDK and 15.2.0 SDK. I am following the process mentioned here .
I am using a MacOS for development.
I am...
Hi
I am using device manager and store connected devices value on next advertise device should be broadcast as bonded
static uint32_t device_manager_evt_handler(dm_handle_t...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
I am making a BLE device that uses 7 ADC inputs. Most of the inputs need to read at 1hz or so. Two of these inputs are of interest
The first is a heart-rate signal that...
Hi,
I want to measure ADC for 3.3V
Using formula
RESULT = [V(P) – V(N) ] * GAIN/REFERENCE * 2 (RESOLUTION - m)
Rearranging eqn:
Vin = ( RESULT*REFERENCE)/(2 (RESOLUTION...
Hi,
Does every nrf9160 chip have its unique chip ID? if yes, is it the one which can be read by the AT command AT+CGSN ? and can it be used as the board serial number? ...
