I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi
I just downloaded the nRF connect v2.6.0 - Programmer, but i don't what i have to do to start writing the code.
I only get 2 ``Boxes``, and one of them is called File...
Hello,
I was wondering if there was a way to use the NRF SDK for Mesh DFU example without a serial port. Currently I have 2 Nordic Thingy52s with no serial ports so I cannot...
I am trying to erase the EnOcean switch data without erasing the board. node_reset() function isn't erasing the EnOcean switch data after commissioning.
I would like to...
I am using the example nRF5_SDK_15.2.0_9412b96/examples/proprietary_rf/gzll/gzll_ack_payload.
I tried to modify the default PAYLOAD_LENGTH to 32,but the speed I tested is...
Hello,
This is Jahnavi.I am having 3 nrf52 DK boards and I have to make mesh configuration with those 3 devices.How to connect the nodes of the mesh with group Key?
What...
Hi,
I create my application image using nrfutil like this :
Everything was working great so far but for test purpose I added one argument to this line :
I...
I'm working with nrf52840
i was working on one of examples of BLE and after editing the code 'then burned it on the kit
the code is burnt on the kit , but isn't executed...
I'm having trouble debuging an external module with the j-link included in the nRF52840 DK. I'm using the debug output provided in the P19 connector.
The connections are...
I am using the nRF5 SDK Version 15.2 and nRF52840-DK to model a custom service containing five characteristics along with the standard BMS and DIS service provided in the...
Hi,
when sending small 11 byte messages on the mesh nrf52840 S140 mesh 3.1 Only every 3rd message return status 0, the rest returns status "Device is busy". I know this...
I am looking at routine 'spi_master_using_nrf_spi_mngr', I found "#define NRF_PWR_MGMT_CONFIG_FPU_SUPPORT_ENABLED 1 " in the sdk_config.h file. Is this part of the routine...
Based on this question I've assumed that it's possible to use nRF52832 for providing Bluetooth connectivity to an embedded Linux platform.
A quote from the github repo...
Hello.
I merge into embOS start project some peripheral example from Nordic like the Serial and spi ones. In the Start I chose the CMSIS one without a specific MCU and bring...
hi,
i am using sdk 14.2.0 multi-link central example,
my aim is to connect multiple sensors (up to 8 ble peripheral devices) with extended packet enabled.
sensors will...
